USER MANUAL
HANDHELD VACUUM CLEANER AP005
USER MANUAL
operating instructions
IMPORTANT NOTICES!
PLEASE KEEP FOR REFERENCE!
On this page, you will find all illustrations referenced in these operating instructions. Open the page before reading the operating instructions.
- Please read this user manual carefully before use to avoid any accidents caused by improper use. Refer to the FAQs or consult the seller if any problems occur. Do
not attempt to solve an unknown problem without proper instruction. - Please do not use accessories that are not approved by the manufacturer. If the cleaner malfunctions due to this, the warranty will be automatically suspended.
- Please check whether the product is damaged after unpacking.
- Please keep the machine away from children and pets for safety reasons.
- If a malfunction occurs, immediately unplug the power cord and do not attempt to use the defective product.
main technical parameters
| Product Category | UV Vacuum Cleaner | ||
| Rated Power | 500W | Capacity | 500ml |
| Rated Frequency | 50HZ | Rated Voltage | 120V |
| Moder Number | AP005 | Cord Length | 4m/13.2ft |
packing List
| Name | Quantity | Name | Quantity |
| UV Vacuum Cleaner | 1 | User Manual | 1 |
- Dust cup removal
- Handle
- Motor
- Air Outlet
- Brush
- Dust cup
- On/Off Switch
- Sensor Light
- UV light
- Ultrasonic Components
- Brush Cover
- Brush
- Brush Cover Locks
- Sensor Light
- Brush
- Roller
- Air Outlet
- Brush Cover Locks
- Brush Cover
- Brush
frequently asked questions
| Problem | Possible cause | Solutions |
| Replacement filter | For purchases, please contact customer service | The filter is washable and reusable. It’s recommended to replace it based on your actual usage and cleaning situation |
| UV Light does not work | Two infrared sensors are too far away from the clean object. | Place the machine back onto the clean surface. (Distance to object less than 30mm, angle less than 30°) |
| The two infrared sensors are blocked by dust | Put the machine back on the cleaning surface. (Less than 30mm away from the object, while the angle is less than 30°) | |
| Check if the UV lamp is broken | Contact customer service for replacements | |
| Suddenly stopped using | Overheat Protection | Allow the machine to cool down for 20-30 minutes before reuse |
| Check if the power plug is inserted correctly | Reconnect the plug or change to another power source | |
| Check if the cleaner is blocked | Clean the blockage and wait for 30 mins after cooling, then turn it on again | |
| Can’t hold the trash | The air inlet is blocked | Clean the dust cup and the filter |
| The motor is not working | Check if the power plug is inserted correctly | Plug it back into the power outlet firmly |
| Check if the power outlet has power | Ensure the power outlet has power/Or change to another power source | |
| Check if the switch is turned on | Turn it on | |
| Suction weakened | Check if the filter is full of dust | Clean up the dust and wash them with water, dry them up before reuse |
| Check if the dust cup is too full | Clean up rubbish in time | |
| Abnormal sound | Check if the filter is blocked | Stop using and remove the blockage in time |
| Power cord is damaged | Please contact customer service | |
If the above does not solve your problem, please contact customer service in time.
cleaning and maintenance
Daily Cleaning: Remove the dust cup and filter to clean the dust.
Thorough Cleaning: take out the dust cup and the filter. Rinse them all under water, or wash them in the water.
Note: All the accessories must be completely dried up before reassembled and reuse.
Note:
- Too much dust and stain on the lamp will affect its penetration. Please clean the UV lamp if necessary.
- Wipe the transparent plate on the UV lamp with a clean cloth.
how to use
- Plug in the power plug and press the power switch.
- One-key Operation: One press the power switch to turn on & off the machine.
- For Bed, Mattress, Pillow, Sofa, Plush Toys, Pet, Bed, Sheets, Clothes, Carpets, Curtains etc.
- Move the machine forward and backward, make sure the 2 safety switches are pressed on the
cleaning surface when moving.
- Make sure to place the machine on a clean surface (distance less than 30 mm from objects, angle less than 30°), or the UV lamp won’t turn on for safety reason.
- Overheat protection will be triggered automatically when running too hot and the device may stop working, wait for a while to cool down then reuse.
Safety Cautions
Don't use this device to suck water or any flammable and corrosive liquids such as kerosene, gasoline, paint, detergent, etc,.
Don't suck hazardous dust such as cement, talcum, calcimine. It will block the filter parts, which will cause the motor to burn out, and even cause fire or explosion. If the above happens, please clean the filter parts in time.
When the machine is not in use, please unplug the power plug. When inserting or unplugging the power supply, please hold the plug and donʼt pull on the power cord.
When cleaning this device, please use a damp cloth with water or neutral detergent, don't use gasoline, banana oil(lacquer thinner) etc., otherwise it may cause the shell to crack or fade.
Don't suck large hair clot, spitball, burning cigarettes, uncooled cinders and charcoal, and other items that are easy to block or damage the inlet, otherwise it may cause motor failure or shell deformation, or even fire or explosion. If the above happens, stop using and unplug the device in time to clear them.
Don't use the device on objects that are prone to discoloration or cracked surfaces.
Make sure the dust cup is empty before storage. Place it at a dry and ventilated place.
WARNING
Risk of damage to the eyes and skin!
Ultraviolet rays are harmful to the eyes and skin. Never expose yourself or other people and animals to direct or reflected rays! If you come into contact with the rays, consult a doctor immediately.
DANGER
Danger of Electric Shock
Never touch the device and the connecting cable with wet hands when the device is connected to the mains power.
If the device falls into water while it is connected to the mains power, pull the plug out of the plug socket immediately! Only after this should you retrieve the device from the water.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important: Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
